|
|
08-19-2017, 02:39 PM | #1 |
First Lieutenant
68
Rep 378
Posts |
Whats everyone running for wheel offsets?
Looking at 19x9 et 20 and 19x10 et 35
curious if anyone else is running this setup, or if it will fit.
__________________
2011 BMW Z4 35i | FBO | VTT Stg 2+ (EK, 20T clipped)| Motiv PI| Motiv Tuned | Fuel-IT Stg 2 + inline fuel pump | Spec Stg 3+ clutch | MFactory flywheel | 606whp 575Lbs |
|
08-19-2017, 06:10 PM | #2 |
Lieutenant
162
Rep 561
Posts |
19x9 et35 245/35/19
19x10 et38 275/30/19 Flush fit at the fender, rubs through the inner liner, slightly. Perfect otherwise. Not sure about inside clearance.
__________________
2011 35i MT Atacama ... lots of bits. Full Öhlins TTX custom suspension. Build thread.
Build sheet. Currently finishing suspension, fuel, ignition system with Barry Battle @ 3DMMotorsport. |
Appreciate
0
|
08-21-2017, 02:33 PM | #3 |
Captain
166
Rep 906
Posts
Drives: 2008 535xi / 2011 Z4 35Is
Join Date: Jan 2011
Location: Indiana
|
19x8.5 ET 35
19x9.5 ET 35 I am using spacers from ECS. A 12.5mm and 15mm with a stud conversion kit. Looks great. I also am rubbing through the rear plastic liner. Almost made it far enough to where it will quit rubbing soon. |
Appreciate
0
|
08-21-2017, 08:20 PM | #4 |
New Member
1
Rep 11
Posts |
Wheels
I had 19" wheels but went with 18" due to continued wheel damage ever time I hit a sharp bump. No issue with rubbing. I have BC coil overs but didn't lower the car.
Factory 8Jx19 ET29 9Jx19 ET40 New wheels and tires Bayern Spartan 18x8.5 30 offset 18x9.5 35 offset I running PSS 245/40R18 and 275/35R18 |
Appreciate
0
|
08-23-2017, 01:57 PM | #5 |
Lieutenant
253
Rep 411
Posts |
The BMW M437 wheel is a good example for offset since some E89 Z4 owners usually go this route for 19" upgrading
The M437 are (front)9x19" ET29 and (rear) 10x19" ET40 A 235-245 tire for the front and 275-285* possibly* for the rear - stock height though. Last edited by BaaQaf; 08-23-2017 at 02:04 PM.. |
Appreciate
0
|
08-24-2017, 09:39 AM | #6 |
First Lieutenant
62
Rep 370
Posts |
Why doesn't this thread have any pictures to show the fitment of everyones wheels? lol
My fronts are 19x8 ET 35 w/10mm spacers and 235/35 tires... and the rear are 19x9.5 ET 35 with 275/30 tires. The car is lowered on H&R coils and the rear rubbed the inner plastic a little until it clearanced itself
__________________
2009 Z4 35i 6mt, SpeedTech 6266 Gen2 turbo kit, Tial WG, VRSF 7.5 race IC, ER charge pipe, Tial BOV, Radium Fuel cell w/ surge tank and twin Walbro 525 pumps, Radium FPR and return line, Bluetooth ethanol sensor, Phoenix intake manifold w/PI, JB4 tuner, PR coil packs, Custom oil cooler, ECS Radiator, Spec 3+clutch, Mfactory flywheel, single 3.5" into dual 3" exhaust, H&R springs, 19" TSW wheels, 235/19 & 275/19 RE11 tires
Last edited by Eracer76; 09-11-2017 at 12:40 PM.. |
Appreciate
1
BaaQaf253.00 |
09-06-2017, 07:53 PM | #8 |
Lieutenant
162
Rep 561
Posts |
Quote:
Filippo
__________________
2011 35i MT Atacama ... lots of bits. Full Öhlins TTX custom suspension. Build thread.
Build sheet. Currently finishing suspension, fuel, ignition system with Barry Battle @ 3DMMotorsport. |
Appreciate
2
BaaQaf253.00 talhagursoy103.50 |
09-11-2017, 12:42 PM | #9 |
First Lieutenant
62
Rep 370
Posts |
LOL, yeah it worked for a little while, so much for that though! Back to using Facebook I guess
__________________
2009 Z4 35i 6mt, SpeedTech 6266 Gen2 turbo kit, Tial WG, VRSF 7.5 race IC, ER charge pipe, Tial BOV, Radium Fuel cell w/ surge tank and twin Walbro 525 pumps, Radium FPR and return line, Bluetooth ethanol sensor, Phoenix intake manifold w/PI, JB4 tuner, PR coil packs, Custom oil cooler, ECS Radiator, Spec 3+clutch, Mfactory flywheel, single 3.5" into dual 3" exhaust, H&R springs, 19" TSW wheels, 235/19 & 275/19 RE11 tires
|
Appreciate
0
|
10-25-2017, 10:00 AM | #11 |
Registered
0
Rep 2
Posts |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|