|
|
09-14-2023, 02:54 PM | #1 |
Enlisted Member
2
Rep 42
Posts |
Idrive Controls & unknow wires
https://ibb.co/tY6xRZC
this stop working for some reason I'm unable to control the screen because this don't work is there a fuse or something for this? I also found these two wires hanging down on the bottom driver side and passanger side. Im not sure where they go connected of it it's for the speakers. Driverside: https://ibb.co/sbf5mGW Passanger side: https://ibb.co/chyyVCK Last edited by Djflacoent; 09-14-2023 at 03:00 PM.. |
09-14-2023, 04:22 PM | #2 |
Lieutenant
164
Rep 548
Posts |
Fuse 27 supplies the controller, check this first.
Those two wires look like the footwell lights, correct wire colours
__________________
Dave
2011, E89 23i, Grey with Red leather.... relatively basic (getting less and less basic with every new retrofit)! My Z4 E89 YouTube channel... https://www.youtube.com/channel/UCtt...0vHFUQnoEvKB2Q |
Appreciate
0
|
09-15-2023, 02:38 PM | #3 |
Enlisted Member
2
Rep 42
Posts |
|
Appreciate
0
|
09-15-2023, 02:58 PM | #4 |
Lieutenant
164
Rep 548
Posts |
Does it light up when the lights are on?
Could be the plug underneath come loose.
__________________
Dave
2011, E89 23i, Grey with Red leather.... relatively basic (getting less and less basic with every new retrofit)! My Z4 E89 YouTube channel... https://www.youtube.com/channel/UCtt...0vHFUQnoEvKB2Q |
Appreciate
0
|
09-15-2023, 09:19 PM | #5 |
Enlisted Member
2
Rep 42
Posts |
|
Appreciate
0
|
09-21-2023, 05:58 AM | #7 |
Lieutenant
164
Rep 548
Posts |
Hmm
OK, so you've only got 4 wires going to it. Pins 1 (red with white) & 2 (Brown with black) are the power, straight 12v fed from fuse 27. So although you've checked the fuse I'd suggest checking you've actually got 12v at the pins. If you haven't then check continuity for pin 2 (ground) with any other ground point, or simply check voltage between pin 1 and another ground point. Pins 3 (Orange with green, can high) and 4 (green, can low) are the k-can bus wires. Checking the wire voltage here is a little more complicated, so I'd suggest going for a fault code check at this point.
__________________
Dave
2011, E89 23i, Grey with Red leather.... relatively basic (getting less and less basic with every new retrofit)! My Z4 E89 YouTube channel... https://www.youtube.com/channel/UCtt...0vHFUQnoEvKB2Q |
Appreciate
0
|
09-21-2023, 06:37 AM | #8 | |
Enlisted Member
2
Rep 42
Posts |
Quote:
|
|
Appreciate
0
|
09-21-2023, 04:03 PM | #9 |
Enlisted Member
2
Rep 42
Posts |
So I checked the pins volage and Im getting 13 to 14v. Also I scan the car and I did get this code:
The fault code A559 is related to the battery charge of your BMW vehicle12. It means that terminal 30 was shut down due to low battery charge2. If you see fault code 00a559, it is an indication that the instrument cluster is failing or has already failed, and you will need to replace it3. You can monitor your battery and charging system voltage by using Submenu 9.00 in "Hidden Menu" Scanner says close cir current cutoff relay. Code A559 |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|