|
|
|
Post Reply |
|
Thread Tools | Search this Thread |
04-09-2016, 10:30 PM | #1 |
Lieutenant
162
Rep 561
Posts |
Install advise: front CF spoiler, side skirts and rear diffuser
I did some searches here and on Google with no luck. Has anyone here installed the front CF lip spoiler, CF side skirts, or rear CF diffuser that can pass along tips or reference for doing this job?
Thanks! Filippo |
04-12-2016, 11:26 AM | #2 |
First Lieutenant
68
Rep 378
Posts |
its stupid simple.
for the lip use 3M double sided tape and the screws that come with the lip. The side skirts just screw in. you will need to put the car on jacks to get the screws in. the SF spoiler, again just use 3M tape. make sure you line it up before. it will take you 2 hours at most to do everything...
__________________
2011 BMW Z4 35i | FBO | VTT Stg 2+ (EK, 20T clipped)| Motiv PI| Motiv Tuned | Fuel-IT Stg 2 + inline fuel pump | Spec Stg 3+ clutch | MFactory flywheel | 606whp 575Lbs |
|
Appreciate
0
|
04-12-2016, 08:10 PM | #3 |
Lieutenant
162
Rep 561
Posts |
Interesting ... no screws with my front spoiler. Looks like factory mount points? Possibly existing factory screws? Guess i"ll figure that out... thanks ...
Filippo |
Appreciate
0
|
04-12-2016, 08:11 PM | #4 |
First Lieutenant
68
Rep 378
Posts |
Depends on the lip. My 3D design lip for the non-M bumper came with 4 screws that went into the edge of the stock bumper.
__________________
2011 BMW Z4 35i | FBO | VTT Stg 2+ (EK, 20T clipped)| Motiv PI| Motiv Tuned | Fuel-IT Stg 2 + inline fuel pump | Spec Stg 3+ clutch | MFactory flywheel | 606whp 575Lbs |
|
Appreciate
1
fmorelli161.50 |
09-29-2016, 12:42 AM | #5 |
Lieutenant
162
Rep 561
Posts |
My side skirts came with no mounting hardware. I decided to use BMW expanding plastic rivets (those with the panhead which you press into the rivet). I'll drill out the stock skirts and holes in the CF side skirt to fit the 6mm rivets. I think I'm going to put a long run of 3M automotive double stick tape along the outer edge, just so everything locks in tightly.
Filippo
__________________
2011 35i MT Atacama ... lots of bits. Full Öhlins TTX custom suspension. Build thread.
Build sheet. Currently finishing suspension, fuel, ignition system with Barry Battle @ 3DMMotorsport. |
Appreciate
0
|
09-29-2016, 10:05 AM | #7 |
Lieutenant
162
Rep 561
Posts |
Ah, thanks jts1981. I was scratching my head about the splitter. Heat gun it is ...
Filippo
__________________
2011 35i MT Atacama ... lots of bits. Full Öhlins TTX custom suspension. Build thread.
Build sheet. Currently finishing suspension, fuel, ignition system with Barry Battle @ 3DMMotorsport. |
Appreciate
0
|
10-05-2016, 08:27 AM | #8 | |
Lieutenant Colonel
118
Rep 1,668
Posts |
Quote:
__________________
Enjoying an E89 Z4, F30 320i and Fiat Abarth //
E85 Z4 (sold), E82 128i (sold), Fiat Pop 500 (sold) |
|
Appreciate
1
fmorelli161.50 |
Post Reply |
Bookmarks |
|
|